Подскажите пожалуйста как настроить работу ш-ка и оф карты ПлатформыХД, каким камд лучше пользоваться или несколькими, но не могу понять как использовать связку???
Пост N: 13
Зарегистрирован: 14.07.08
Откуда: Россия, Мирный
Отправлено: 11.05.10 04:54. Заголовок: Wolf пишет: Настрой..
Wolf пишет:
цитата:
Настройка связки в основном нужна для работы официальных карт в картоприёмнике. Один выступает в роли картсервера, другой в роли обычного клиента.
Если я правильно понял, то для того, чтобы карта заработала в картоприемнике можно использовать любую из трех связок. В случае если я использую, к примеру, САМ-модуль Ирдето никакая связка не нужна. А если я хочу расшарить оф. карты на три ресивера с использованием картоприемника, в этом случае дополнительно еще что-то нужно?
anatoly Правильно всё понял. Для CAM модуля конечно связка не нужна. Если хочешь сделать домашний шаринг карты, то в настройках mpcs надо добавить пользователей которые будут иметь доступ к карте. К примеру mpcs.user дописать пользователей.
Пост N: 14
Зарегистрирован: 14.07.08
Откуда: Россия, Мирный
Отправлено: 11.05.10 07:27. Заголовок: Wolf пишет: Правиль..
Wolf пишет:
цитата:
Правильно всё понял. Для CAM модуля конечно связка не нужна. Если хочешь сделать домашний шаринг карты, то в настройках mpcs надо добавить пользователей которые будут иметь доступ к карте. К примеру mpcs.user дописать пользователей.
Спасибо большое. Буду пробовать методом проб и ошибок, потому как пока слабо представляю, что и как делать, но когда-то надо начинать. И, я так думаю, что и на остальных двух ресиверах нужно что-то настраивать.
Wolf, скачал конфиг всё вроде запустил, но, чо то карту Радуги не смог завести(апдейтить), втыкнул в модуль стартанул потом и в картридере пошла. Кстати в Dream-Elite нету папки /etc/tuxbox/config/ я создал её вроде работает, или файлы можно было прям в tuxbox? Работают карты ТК-Сибирь и Радуга(как то странно)
чо то карту Радуги не смог завести(апдейтить), втыкнул в модуль стартанул потом и в картридере пошла.
У меня всё апдейтится, проверь настройки, что бы AU=1 было в конфигах mpcs. Для mgcamd в mg_conf должно быть:
# AU # 00 disable, no emm pids processed # 01 enable, emm pids always processed for soft-au and shared cards # 02 auto, emm started only if channel cant be decoded # 03 process emm pids for network cards update only A: { 01 }
# key update (sum 01 or 02 with 04) # 01 update only new keys, default setting # 02 update all keys (used for valid PMK checking) # 04 enable TPS au # + tps au pid U: { 02 }
И в newcamd.list примерно вот так:
CWS = 127.0.0.1 11111 login password 0102030405060708091011121314 au
Отправлено: 12.05.10 09:41. Заголовок: Wolf, ага всё работа..
Wolf, ага всё работаеть! ПС Блин как я доволен ресивером, кажись я нашел своё счастье. После длинного пути поисков ХД-ресивера: GI-S890, GI-S980, Азбокс-премиум и наконец Gi S9895
Отправлено: 15.05.10 15:49. Заголовок: Если хочется просто ..
Если хочется просто использовать карту Платформы, но вам сложно и непонятно настраивать связки эмуляторов, то есть простой выход - просто скачиваете и устанавливаете плагин OSCam 0.99.4 - CCcam 2.1.4 и конфиги к нему из панели VTI - вставляем карту в верхний слот и запускаем эмулятор - все показывает!
В принципе я полагаю достаточно и одного cccam 2.1.4.
сли хочется просто использовать карту Платформы, но вам сложно и непонятно настраивать связки эмуляторов, то есть простой выход - просто скачиваете и устанавливаете плагин OSCam 0.99.4 - CCcam 2.1.4 и конфиги к нему из панели VTI - вставляем карту в верхний слот и запускаем эмулятор - все показывает!
В принципе я полагаю достаточно и одного cccam 2.1.4.
Что необходимо исправить в конфигах, для автоапдейта карточки Платформы?
Добрый день уважаемые форумчане. Поставил имидж Dream-Elite, установил связку mgcamd1.31+newcs1.67 карта не пошла в картоприёмнике, на аналогичном имидже на дриме 800 на этой же связке пошла. Помогите пожалуйста запустить карту. Заранее спасибо. С уважением Сергей.
Отправлено: 21.05.10 23:07. Заголовок: rolex пишет: Если х..
rolex пишет:
цитата:
Если хочется просто использовать карту Платформы, но вам сложно и непонятно настраивать связки эмуляторов, то есть простой выход - просто скачиваете и устанавливаете плагин OSCam 0.99.4 - CCcam 2.1.4 и конфиги к нему из панели VTI - вставляем карту в верхний слот и запускаем эмулятор - все показывает!
установил плагин OSCam 0.99.4 - CCcam 2.1.4 и конфиги к нему из панели VTI вставил карту Платформы в верхний слот ничего не пошло,в чем может быть причина ?
Отправлено: 22.05.10 06:57. Заголовок: aaleks74 вот мой ..
aaleks74
Вот мой конфиг ,работают карты Ориона и Платформы в нем без проблем с апдейтом. Причина еще может быть в том, что карту вставляете не той стороной
######################## CCcam.cfg ############################ # CCcam team uvadi CCcam v2.1.2 # # Special greets go to all our friends all over the world, you know who you are! # # Specjalne podziekowania dla Ludzi z Polski, dzieki ktorym jest duzo nowych funkcji w wersji 2.0.0 # Ostatnim razem zapomnielismy o nich wspomniec w readme. DZieki Chlopaki! #
###################################################################### # friends # ###################################################################### # syntax for to add a friend user to CCcam with the max up hops limit (default = 5) # sharing of emus (default = 1), allow emm (default = 1), and optional # downshare limits per share (default = no limits) and optional # downshare limits per share based on caid:id:sid # and optional timeslots in which share is valid (to block channels on box of children after 19:00 for instance) # if no timeslot is defined 24 hrs a day is used # emus are shared only one level down, even if no limits given # # max username length 20 # password length 'unlimited' # #F: <username> <password> <uphops> <shareemus> <allowemm> ( { caid:id(:downhops), caid:id(:downhops), ... } { caid:id:sid, caid:id:sid, ... } { begintime-endtime, ... } ) hostname/ip address # # example: # # F: user1 pass1 # # user1 gets all our shares at max 5 hops from us # (our local cards + max five hops away). He can share down to his own # clients. He also receive emu shares (if he has 'yes' behind his C: entry), # and is allowed to send us emm. # # F: user2 pass2 0 1 0 { 0100:000080, 0622:000000:1, 0500:000000:2 } # # user2 gets only our local cards but no 0100:000080. # and our 0622:000000 cards only for himself (1 hop down), # and 0500 cards for himself plus one additional hop down. # He also gets our emus, and is NOT allowed to send us emm (updates). # # F: user3 pass3 5 0 1 { 0:0:3, 0100:000080:1 } # # user3 gets all cards at a maximum of 5 hops away from us, # and get's to share them down two further levels beyond his own level. # But he is not allowed to share 0100:000080 down to other users. # He gets no emus from us, and he is allowed to send us emm. # # F: user4 pass4 5 0 1 { 0:0:3, 0100:000080:1 } { 0100:000080:15df } # # user4 gets all cards at a maximum of 5 hops away from us, # and get's to share them down two further levels beyond his own level. # But he is not allowed to share 0100:000080 down to other users. # He gets no emus from us, and he is allowed to send us emm. # He is also not allowed to view channel 0100:000080:15df # # F: user4 pass4 5 0 1 { } { } { 12:00-17:00, 19:00-20:00 } # # user4 gets all cards at a maximum of 5 hops away from us, # and get's to share them down two further levels beyond his own level. # the share is only valid between 12:00 and 17:00 and between 19:00 and 20:00 # outside these hours the share will not give cw's to the client # # # F: user5 pass5 5 1 1 { } { } { } 192.168.1.1 # # user5 gets all cards at a maximum of 5 hops away from us # user5 is only allowed to connect from the host 192.168.1.1 #
###################################################################### # connections # ###################################################################### # syntax for to add a client connection to other CCcam # add yes on end to use friends emus (non public private key/emu,etc...), # but only works when corresponding F line on server has '1' for <shareemus> # optional limits just like F line, but for incoming shares (ignore shares more than 'uphops' away) # #C: <hostname> <port> <username> <password> <wantemus> ( { caid:id(:uphops), caid:id(:uphops), ... } ) # #note: if {} limits are added, <wantemus> cannot be omitted. Use either yes or no. # # example: # # C: someserver.somedomain 12000 user1 pass1 # C: 192.168.1.2 12000 user2 pass2 # connects to CCcam without use of friends emus # # C: 192.168.1.2 12000 user3 pass3 yes # connects to CCcam, and receives friends emus also.
# syntax for add gbox connection # #G: <pass> <localhost> <localport> <peerpass> <peeraddress> <peerport> # # support optional limits just like C line (ignore shares more than 'uphops' away) # { caid:id(:uphops), caid:id(:uphops), ... } # # example: # # G: AABBCCDD my.address.tv 2500 12345678 peer.address.tv 2500
###################################################################### # Other config settings # ###################################################################### # server shall listen on this port pro incoming connections # default port is 12000, disable server with parm -s or set port 0 # #SERVER LISTEN PORT : 12000
# server can give some info about server and client connections # and cardinfo using telnet or webbrowser. # # Switch on/off access to info # default is yes # #ALLOW TELNETINFO: no #ALLOW WEBINFO: no
# Show extended client info when showing client list # default is yes # #SHOW EXTENEDED CLIENT INFO : no
# The webinfo service can be protected with a username and password. # This is switched off by default # #WEBINFO USERNAME : <username> #WEBINFO PASSWORD : <password>
# The telnetinfo service can be protected with a username and password. # This is switched off by default # #TELNETINFO USERNAME : <username> #TELNETINFO PASSWORD : <password>
# default port for telnet is 16000 # default port for web is 16001 # supported commands: # info # activeclients # clients # servers # shares # providers # entitlements # example use: # echo servers | telnet localhost 16000 # go with your browser to http://ip_CCcam_server:16001 # #TELNETINFO LISTEN PORT : 16000 #WEBINFO LISTEN PORT : 16001
# time in seconds to keep On Screen Display active. # default is 0 (turned off) # #ZAP OSD TIME : 3
# username used to show popup (default : root) #OSD USERNAME : root
# password used to show popup (default : dreambox) #OSD PASSWORD : dreambox
# port used to show popup (default : 80) #OSD PORT : 80
# Serial reader config. Add as many as you have attached too your system # replaces old name 'PHOENIX READER PATH', but still works. # default is none # optionally add readertype : phoenix,mouse,uniprog,sc8in1,smartreader+ # (when non readertype given defaults to uniprog (e.g. for mastera)) # # SERIAL READER : <device> <type> # # example # #SERIAL READER : /dev/tts/0
# Serial reader smartcard write delay. # Setting to finetune smartcard write speed, optimal setting depends on speed of system, and # speed of card. Default value is calculated, but can overrule by setting. # Use number of microseconds delay between bytes, 0 = no delay, -1 = calculated default # Note: huge difference between values 0 and 1, because of schedular overhead # # SMARTCARD WRITE DELAY : <device> <delay> # # example, 10ms write delay on smartcard in reader attached to /dev/ttyUSB0 # #SMARTCARD WRITE DELAY: /dev/ttyUSB0 10000 # # NOTE on sc8in1; because 8 smartcards are used on the same devicename, use # devicename_0 .. devicename_7 for settings which require devicename to make # settings per smartcard. example /dev/ttyS0_0, /dev/ttyS0_1 .. # example, 8ms write delay between bytes to smartcard on last sc8in1 channel, attached to /dev/tts/0 # #SMARTCARD WRITE DELAY: /dev/tts/0_7 8000
# Smartcard clock speed override # Setting override specified speed for smartcard. # Don't add setting unless you're sure what you're doing. # In 99% of the cases the reader selects the optimal speed. # Adding this setting either slows your card down, or might destroy it. # # SMARTCARD CLOCK FREQUENCY : <device> <freq> # # example # #SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 5500000
# if timing should be shown in OSD and debug output # default is no (turned off) # #SHOW TIMING : yes
# enables mini OSD which shows server(type), cardreader, keys or fta only # default is no (turned off) # #MINI OSD : yes
# turns debugging on and off # default is no (turned off) # #DEBUG : yes
# should CCcam try to read and parse newcamd.conf for server connections # default is no (turned off) # #NEWCAMD CONF : yes
# configure what EMM blocker you want. Add as many as readers you have attached # default is blocking nothing # # B: /dev/sci0 01 # 00 - nothing # 01 - sa blocked # 02 - ua blocked # 04 - ga blocked # and sum of for combinations # #examples # #B: /dev/tts/0 07 #B: /dev/sci0 01
# disable all local EMM readers # saves lots of CPU, but you won't get any updates anymore # (unless you get updates from your clients) # # default: no # #DISABLE EMM : yes
# with this setting you can # allow a client on two hops away # to send the updates to the cardserver # # default : no # #EXTRA EMM LEVEL : yes
# with this setting you can # configure how many emm listeners are started. # for example use 2 when recording # and viewing different systems and both need constant updates # # default : 1 # #EMM THREADS : 1
# overrule the irdeto camdata (64 byte hex) # trailing zero bytes can be omitted # default for unknown ASC's is 11 22 33 44 55 66 77 88 00 00 .. 00, known ASC's have other defaults # # CAMDATA: <device> <byte1> <byte2> <byte3> <byte4> <byte5> <byte6> ... <byte64> # #example, when only the first 15 camdata bytes are nonzero # CAMDATA: /dev/sci0 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff
# what Softcam.Key should CCcam try to read # defaults to /var/keys/SoftCam.Key # #SOFTKEY FILE : /var/keys/SoftCam.Key
# what AutoRoll.Key should CCcam try to read # defaults to /var/keys/AutoRoll.Key # #AUTOROLL FILE : /var/keys/AutoRoll.Key
# what constant.cw should CCcam try to read # defaults to /var/keys/constant.cw # file content can be like # # ca4:id6:sid4:pmtpid4:ecmpid4:key16(01 02 03...) # #STATIC CW FILE : /var/keys/constant.cw
# in this file you can configure what CAIDs CCcam should prefer or ignore # defaults to /var/etc/CCcam.prio # file content can have ignores (I) and prio lists (P) # # note 1: I line affects both for ecm and emm (receive no emm on ignored systems) # P line only affects ecm choice (emm still received for all available systems, not just the priority system) # # note 2: ident 0 means 'all idents'. So 'caid:0' is the same as 'caid'. # # note 3: for some systems (e.g. nagra (caid 18xx)), the ident is not known at the time the # prio lists are checked. In that case, matching is done on caid only, even if the P line # defines nonzero idents. So for example '1801:401' behaves the same as '1801' in a P line # I lines work differently, they are checked two times, once before ecm or emm is received, again # after ecm or emm are received (and nagra ident should be known) # P lines are only checked once, before ecm received. # # note 4: if a P line contains caid:ident pairs which are not available for the current # channel, that P line is not used for that channel. # Example, channel has systems 626, 1801:401 then P line with "1801,100:96,626" is ignored by that channel, # because channel doesn't have 100:96. # But P line with "1801" works, and also "626,1801" will work for channel # # note 5: P lines are parsed in the order in which they are found in the prio file. # Only the first matching P line is used # # situation 1: ignore allways this caid, all idents, on all channels # I: caid # # situation 2: ignore allways this caid/ident pair # I: caid:ident # # situation 3: ignore this caid/ident pair, on channel 'sid' # I: caid:ident:sid # # situation 4: when both caid1 and caid2 exist for a channel, prefer caid1 over caid2 # P: caid1, caid2 # # situation 5: when caid1:ident1 till caidN:identN exist for a channel, use them in order of this list. # P: caid1:ident1, caid2:ident2, .., caidN:identN # # situation 6: when caid1:ident1 till caidN:identN exist for channel 'sid', use them in order of this list. # Sid on first caid/ident pair identifies sid for which list is used. All other sids ignore this list. # P: caid1:ident1:sid, caid2:ident2, .., caidN:identN # #CAID PRIO FILE : /var/etc/CCcam.prio
# # In this file all provider idents are defined # The info from this file is being used in the web interface # format: # <caid><ident> "Provider description" # # PROVIDERINFO FILE : /var/etc/CCcam.providers
# # In this file all channel idents are defined # The info from this file is being used in the web interface # format: # caid:ident:sid "Channel description" # # CHANNELINFO FILE : /var/etc/CCcam.channelinfo
# write wrong logins to file # defaults is off # #LOG WARNINGS : /tmp/warnings.txt
# global setting for stealthy login to newcamd/newcs server, N line can overrule # stealth modes: 0 = disabled, 1 = mgcamd new, 2 = mgcamd old, 3 = evocamd, 4 = generic # default: 0 # #NEWCAMD STEALTH : 0
# load balancing between identical cards, list device names of card readers containing identical cards, # optionally followed by a list of service id's which are to be excluded from loadbalancing # # LOADBALANCE : <device1> <device2> .. <devicen> { <exceptsid1>, <exceptsid2> .. , <exceptsidn> } # # multiple loadbalance groups can be configured, by adding multiple lines # warning: restart is required, when loadbalance group config changes # #example 1: load balance requests for three identical cards # # LOADBALANCE : /dev/ttyS0 /dev/ttyS1 /dev/ttyS2 # #example 2: load balance requests for two almost identical cards, sid 0df3 and 0de1 are only available #on one of the cards, so requests for these sids shouldn't be loadbalanced # # LOADBALANCE : /dev/ttyS5 /dev/ttyS6 { 0df3,0de1 }
# in version 1.2.1 and lower there was a problem which could lead to disconnecting clients # in version 1.4.0 network load was significantly reduced # in version 1.7.0 dangerous password bug was fixed # in order to take advantage of these fixes, all clients should upgrade # with this setting you can force that clients at least use a certain version otherwise they are denied when logging in # # default : accept all versions # #example 1: avoid disconnecting clients problem # #MINIMUM CLIENT VERSION : 1.3.0 # #example 2: achieve network load decrease # #MINIMUM CLIENT VERSION : 1.4.0 # #example 3: don't allow potentially wrong passwords (pre 1.7.0 has password bug) # #MINIMUM CLIENT VERSION : 1.7.0
# Irdeto smartcards: option to disable smart chid checking for irdeto smartcards. # Default, only chids advertised by card are accepted. # This avoids a lot of unwanted card traffic # # But if smartcard has hidden/unknown chids, all chids should be tried. # In that case specify 'TRY ALL CHIDS' option for cardreader. # Use with care, enabling option causes more card traffic. # Only use setting when some channels don't work without it. # note: if even this setting don't help decode all channels, try using # commandline arg -l, to disable all self-learning features (warning: slower) # #TRY ALL CHIDS : <device> # #example: card in /dev/ttyUSB0 gets ecm for all possible chids, not #just the chids it officially supports # #TRY ALL CHIDS : /dev/ttyUSB0
# perform smartcard post init commands # # POSTINIT : <device> <filename> (<autodelete>) # # send commands in 'filename' to 'device', and delete 'filename' when # optional 'autodelete' argument nonzero # #example: # #POSTINIT : /dev/sci0 /tmp/postinit # #example /tmp/postinit contents: #c134000003000000 #c13201000a
# Option to override autodetected dvb api version. Restart needed. # #DVB API: <value> # # <value> -1 = no dvb, 1 = dvb api 1, 3 = dvb api 3 # # WARNING: only use when autodetect fails! # #example, disable nonworking dvb hardware: #DVB API: -1
# Option to set global share limits # #GLOBAL LIMITS: { caid:id(:downhops), caid:id(:downhops), ... } # #example: # #GLOBAL LIMITS : { 0100:000080, 0622:000000:1, 0500:000000:2 } # # all users get no 0100:000080. # and our 0622:000000 cards only for themself (1 hop down), # and 0500 cards for themself plus one additional hop down. # global limits are overridden by client specific limits (see F:)
# Option to reject shares with less than required downhops on clientside # #MINIMUM DOWNHOPS: <value> # # default: 0 (don't ignore any shares) # #example: # #MINIMUM DOWNHOPS: 1 # # ignore shares that have less than 1 'downhops' (i.e. can not be shared # further down to other clients)
# Option to ignore all shares that go through a certain node # #IGNORE NODE: <nodeid> # #example, ignore two nodes: # #IGNORE NODE: ccd536ab515767ad #IGNORE NODE: aad536ab515761af
# The seca handler is used to better support simulcrypt on the same ident # # With this setting you can change the behaviour of how SECA has to be used # This setting is ignored unless SECA2/SECA3 simulcrypt is detected!! # # When disabled CCcam behaves like previous versions # # When "prefer SECA3 over SECA2" is enabled try to use SECA3 ecm first, then SECA2 # # When "Ignore SECA2" is enabled, ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle # # When "Ignore SECA3" is enabled, ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle # # # The following settings can be used # # SECA HANDLER: <value> # <value> : 0 = disabled, 1 = prefer SECA3 over SECA2, 2 = prefer SECA2 over SECA3, 3 = Ignore SECA2, 4 = Ignore SECA3 # # default: 1 # # Example try to use SECA3 ecm first, then SECA2 #SECA HANDLER: 1 # # Example try to use SECA2 ecm first, then SECA3 #SECA HANDLER: 2 # # Example to ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle #SECA HANDLER: 3 # # Example to ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle #SECA HANDLER: 4
# Configure limited list of accepted sids for smartcard # When omitted, all sids are allowed. # (can work together with LOADBALANCE configuration, or for standalone cards) # # SMARTCARD SID ASSIGN : <device> <maxnumberofsids> { <sid1>, <sid2>, ... <sidn> } # # <device> is the reader devicenode # <maxnumberofsids> limits the total number of sids assigned to the card (0 = use length of sid list) # { <sid1>..<sidn> } lists the sids that are assigned to the smartcard, when omitted, <maxnumberofsids> is used to auto assign sids # # when <maxnumberofsids> is larger than the length of the sidlist, the remainder of the sids are auto assigned, till the list reaches <maxnumberofsids> # Check entitlement output for realtime assignment list # # WARNING: when SMARTCARD SID ASSIGN config changes, restart is required before settings take effect # #example1: smartcard in device /dev/ttyUSB0 only handles requests for sids df3, df4, df5 # # SMARTCARD SID ASSIGN : /dev/ttyUSB0 0 { 0df3,0df4,0df5 } # #example2: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, auto assigned in the order of occurance. A request for a 6th sid will be denied. # # SMARTCARD SID ASSIGN : /dev/ttyUSB0 5 # #example3: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, 3 of which are df3, df4, df5, remaining 2 are auto assigned # # SMARTCARD SID ASSIGN : /dev/ttyUSB0 5 { 0df3,0df4,0df5 }
- просто скачиваете и устанавливаете плагин OSCam 0.99.4 - CCcam 2.1.4 и конфиги к нему из панели VTI
может поблема в том что плагин устанавливается затем конфигурируется,а при устаноке конфигов в конце лога пишет - nothing to be done ?перевода нормального не смог найти (ничто делать)непонятно,может конфиги не устанавливаются ?
Все даты в формате GMT
3 час. Хитов сегодня: 1
Права: смайлы да, картинки да, шрифты нет, голосования нет
аватары да, автозамена ссылок вкл, премодерация вкл, правка нет